Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 52

Страница: 52 / 160

Chapter 1. Programming Site Data

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

1.7.6

Setting Up Serial Communications

The Model DF868 flowmeter can transmit stored data and displayed readings to a remote ANSI terminal or a

personal computer by connecting the meter’s RS232 interface to the serial port of the PC. In addition, the Model

DF868 can receive and execute remote commands via this link.The meter can also be configured with a MODBUS

option card for MODBUS (RS485) communications, a Foundation Fieldbus option card for Foundation Fieldbus

communications, or a MODBUS/TCP option card for MODBUS communications over the Ethernet, if desired.

Note:

To set Fieldbus communications parameters, see Appendix D,

Foundation Fieldbus Communications

Use the

COMM

submenu to set the RS232, MODBUS, Ethernet and MODBUS/TCP communications port parameters

and to enter a network identification number. A network identification number is required to use the Panametrics

Instrument Data Manager

PanaView

software. While following the programming instructions, refer to the menu

map in Figure 14 on page 101

To enter the

GLOBAL

menu, press

[F3]=GLOBL.

To enter the

COMM

submenu, press [



and

[F4]

Use the

[F1]-[F4]

and [



keys to select the desired

Baud Rate

Note:

As shown in Figure 14 on page 101, the available rates are 300, 600, 1200, 2400, 4800, 9600 and 19,200 baud.

Use the

[F1]-[F4]

and [



keys to select the desired

UART Bits

. The five available responses are listed in Table 25.

Enter a

Network ID

number between 1 and 254 and press

[ENT]

. The default number is 1

A network ID number is only necessary for communication with the Panametrics

Instrument Data Manager

(IDM) or

PanaView

software. See the software

User’s Manual

(910-185) for more information.

IMPORTANT:

If the network ID number is changed, communication with the Instrument Data Manager or PanaView

must be re-established with the new ID number.

Table 25: UART Bits Options

Option Bar

# Data Bits

# Stop Bits

Parity

8,no

None

8,odd

Odd

8even

Even

7,odd

Odd

7even

Even

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 52 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: