Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 41

Страница: 41 / 160

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Chapter 1. Programming Site Data

1.7.4

Entering Global System Data

While following the programming instructions, refer to the menu map in Figure 14 on page 101

To enter the

GLOBAL

menu, press

[F3]=GLOBL.

To enter the

SYSTM

submenu, press

[F2]

SYSTM

At the

System Units

prompt, press

[F1]

to display parameters and measurements in English units or press

[F2]

display parameters and measurements in metric units.

At the

Totalizer Option

, press

[F1]

to measure totals automatically or press

[F2]

to measure totals manually.

AUTO

is selected above, the meter automatically begins totalizing upon leaving the

User Program

. If

MNUAL

selected, the console key on the keypad may then be used to start and stop the totalizer.
The manner in which the totalizer responds to an error condition may be set in the

I/O

submenu.

Use the [



, [



and

[F1]-[F4]

keys to select the desired

Volumetric Units

for the flow rate display.

Note:

The above option bar shows English units, as an example.

The abbreviations and definitions of all the available volumetric units are shown in Table 15. The choices shown on

the option bar are determined by the selections made at the previous

System Units

prompt screen.

Table 15: Volumetric Units Options

English Volumetric Units

Metric Volumetric Units

GAL/S - U.S. Gallons per Second

L/S- Liter per Second

GAL/M - U.S. Gallons per Minute

L/M - Liters per Minute

GAL/H - U.S. Gallons per Hour

L/H - Liters per Hour

MGD - Millions of U.S. Gallons per Day

ML/D - Millions of Liters per Day

/s - Cubic Feet per Second

/s - Cubic Meters per Second

/m - Cubic Feet per Minute

/m- Cubic Meters per Minute

/h- Cubic Feet per Hour

/h - Millions of Cubic Meters per Hour

Mft

/d- Millions of Cubic Feet per Day

/d - Millions of Cubic Meters per Day

BBL/S - Barrels per Second

BBL/M - Barrels per Minute

BBL/H - Barrels per Hour

BBL/D - Barrels per Day

MBBL/D - Millions of Barrels per Day

Acre-inch/sec -Acre-inches per second

N/A

Acre-inch/min -Acre-inches per minute

N/A

Acre-inch/hr -Acre-inches per hour

N/A

Acre-inch/day -Acre-inches per day

N/A

Acre-foot/sec -Acre-feet per second

N/A

Acre-foot/min -Acre-feet per minute

N/A

Acre-foot/shr -Acre-feet per hour

N/A

Acre-foot/day -Acre-feet per day

N/A

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 41 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: