manualshive.com logo in svg

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 30 / 160

Поделиться
Скачать
Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 30

Chapter 1. Programming Site Data

20

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

1.6.5 Entering Setup Data

The signal limits and response times for the Model DF868 are specified via the 

SETUP

 submenu. While following the 

programming instructions, refer to the menu map in Figure 12 on page 99. The following four submenus are included 

in this section:
•

SIGNL

 - set the parameters related to the transducer signal

•

AVRG

 - specify the response of the meter to step changes

•

INIT

 - initialize all parameters to default values.

•

ADVAN

 - activates options for KV/SS, temperature vs. viscosity, Multi K factors, Mass Flow, Code Length and Active 

Tw Measurement.

Table 14 on page 28 lists default values and limits for 

SETUP

 parameters. Remember to record all programmed data 

in Appendix B, 

Data Records

.

1.

To enter the 

Channel PROGRAM

 menu, press 

[F1]

 or 

[F2] (depending on the desired channel) at the User 

Program

 prompt.

2.

Enter the 

SETUP

 submenu by pressing [



 and 

[F1]

 at the 

Channel PROGRAM

 prompt.

1.6.5.1

The SIGNL Option

Use this option to set the limits for the incoming signal and other parameters affecting the transducer signal. For 

example, the programmed signal strength low limit may be used to determine the trigger point for an alarm.

CAUTION!

The SIGNL default settings are suitable for most applications. Before changing any of these 

parameters, consult the factory.

The signal options are different, depending on whether you have selected Transit-Time or TransFlection in the 

ACTIV

 

submenu. Only after consulting the factory, complete the following steps to enter the signal parameters.

1.

Press 

[F1]=SIGNL to enter the SIGNL submenu.

•

For Transit-Time mode, refer to 

Transit-Time SIGNL Options

 on the next page.

•

For TransFlection mode, refer to 

TransFlection SIGNL Options

 on page 23.

Содержание DigitalFlow DF868

































































































































































Отзывы:

Нет отзывов