Panametrics DigitalFlow DF868 Скачать руководство пользователя страница 46

Страница: 46 / 160

Chapter 1. Programming Site Data

DigitalFlow™ DF868 Multipurpose Ultrasonic Liquid Flowmeter Programming Manual (2-Channel)

Slot X Analog Outputs (cont.)

Use the [



and [



and

[F1]-[F4]

keys to specify the desired

Output Measurement

parameter, as shown in

Table 21.

The

DIAG

option provides access to a wide variety of diagnostics parameters. See Chapter 3,

Diagnostics

, of the

Service Manual

for a complete description of these options.

Note:

The measurement units that appear in these prompts are those selected in the

GLOBL-SYSTM

menu earlier

in this chapter.

Enter a value for the

Base

(low end) of the chosen output range and press

[ENT]

Enter a value for the

Full

(high) end of the chosen output range and press

[ENT]

Use the

[F1]-[F4]

keys to select the desired

Error Option

, the way the display responds during an error condition.

Available options are shown in Table 22.

Press

[F1]

[F4]

to set up another output or press

[EXIT]

to select another slot for set up.

For instructions on setting up additional inputs and/or outputs proceed to the appropriate section. Otherwise, press

[EXIT]

twice to return to the

Global Program

prompt.

Table 21: Output Measurement Options

Option Bar Choice

Description

[F1]

VEL

Flow Velocity

[F2]

VOLUM

Volumetric Flow

[F3]

+TOTL

Forward Totalized Volume Flow

[F4]

-TOTL

Reverse Totalized Volume Flow

[



+ [F1]

MDOT*

Mass Flow

[



+ [F2]

+MASS*

Forward Totalized Mass Flow

[



+ [F3]

-MASS*

Reverse Totalized Mass Flow

[



+ [F4]

= POWER**

Energy Flow Power

[



+ [



+ [F1]

= +ENRG**

Forward Energy Flow

[



+ [



+ [F2]

= -ENRG**

Reverse Energy Flow

[



+ [



+ [F3]

DIAG

Diagnostic

* Available only if

Mass Flow (static)?

YES

**Available only if Energy Option = YES

Table 22: Error Response Options

Option

Display Response

HOLD

Holds the last “good” reading.

LOW

Forces the outputs to the low setpoint.

HIGH

Forces the outputs to the high setpoint.

OTHER

Allows user to enter 4-20 mA error level in mA.

Содержание DigitalFlow DF868

































































































































































Результаты поиска

Содержание DigitalFlow DF868

Отзывы:

Panametrics DigitalFlow DF868, Руководство по программированию, Страница: 46 / 160

Результаты поиска

Содержание DigitalFlow DF868

Отзывы: