The symbol and the word DANGER,
state a direct or immediate dan-
gerous situation that will cause
DEATH OR SERIOUS INJURY if not
avoided.
The symbol and the word WARNING, indic-
ates a potentially hazardous situation. If
you fail to comply with instructions given it
could result in personal injury or loss of life.
Do not start operating the machine
until you have read and understood
the safety precautions.
Always stop the tractor engine or external
power unit before; lubricating, adjusting,
maintaining or repairing the machine. Also,
remove the ignition key to prevent acci-
dental start.
Ensure that there are no people
between tractor and machine during
connecting and disconnecting.
Never allow children to stay near the
machine during operation. Young children
can do unpredictable things
Danger rotating parts. Keep clear of
moving/rotating parts in chamber.
Operator or others close to the machine
must be aware when the bale is unloaded
from the wrapper table. Bales dropped
may roll more than 10 m, or even dropped
prematurely.
Always use the hydraulic securing
valves on the chamber door lifting
cylinders, to ensure that the
chamber door stays in open position
during maintenance or repair.
The net or widefilm is cut with a sharp
knife. Be careful when loading a new roller,
or if any adjustment is done to the knife
system.
All parking of the machine must be
on a firm levelled ground, and
secured with wheel chocks.
Unauthorized personell are not allowed
closer than 5 meters, when the machine is
operating or when maneuvering.
Danger. Film holder/cutter has a
sharp knife and there is a risk of
cutting/crushing injury. Always keep
closed when the machine is not
operating.
Keep clear! Do not enter below bunker or
frame when operating the compactor.
2 SAFETY
16
Содержание Dens-X Compactor
