Oriental motor NETC01-M3 Скачать руководство пользователя страница 5

Страница: 5 / 62

Introduction

−5−

System configuration

RS-485 communication

Master station

MECHATROLINK-

䊢

communication

MECHATROLINK-

䊢

communication

compatible product

MECHATROLINK-

䊢

communication

compatible product

NETC01-M3

Termination

resistor: ON *

RS-485

communication

compatible

products

RS-485

communication

compatible

products

RS-485

communication

compatible

products

The termination resistor for RS-485 communication is built into the product.

CE Marking

Because the input power supply voltage of this product is 24 VDC, it is not subject to the Low Voltage

Directive but install and connect this product as follows.

•

This product is designed and manufactured to be installed within another device. Install the product in an
enclosure.

•

For the power supply of the

NETC01-M3

, use a DC power supply with reinforced insulation on its

primary and secondary sides.

•

Overvoltage category:

Ⅰ

•

Pollution degree: 2

•

Degree of protection: IP20

•

EMC Directive

This product has received EMC compliance under the conditions specified in "Example of

NETC01-M3

installation and wiring" on p.10.
The conformance of your mechanical equipment with the EMC Directive will vary depending on such
factors as the configuration, wiring, and layout for other control system devices and electrical parts used

with the

NETC01-M3

. It therefore must be verified through conducting EMC measures in a state where all

parts including the

NETC01-M3

have been installed in the equipment.

Applicable standards

•

EMI: EN 61000-6-4, EN 55011 group 1 class A

•

EMS: EN 61000-6-2

Hazardous substances

The products do not contain the substances exceeding the restriction values of RoHS Directive (2011/65/
EU).

Содержание NETC01-M3































































Результаты поиска

Содержание NETC01-M3

Отзывы:

Похожие инструкции для NETC01-M3

Бренды по названию

Популярные бренды

Oriental motor NETC01-M3, Руководство пользователя

Результаты поиска

Содержание NETC01-M3

Отзывы:

Похожие инструкции для NETC01-M3

Бренды по названию

Популярные бренды