Opticon MDI-4000 Series Скачать руководство пользователя страница 43

Страница: 43 / 139

MDI-4000 Series Serial Interface Manual

WIME may be able to resolve issues when multi-byte characters are not correctly output with
USB-HID.

Figure 21: COM to HID Output Through WIME

4.2.9

Troubleshooting USB-COM

Use this table to find possible solutions to common USB-COM problems.

USB-COM Troubleshooting

Problem

Possible Solutions

Scan engine is not
recognized by the PC

•

Make sure the USB cable is properly connected.

•

Make sure that the connected USB port is operating properly.

•

If you are connecting to wireless devices, like Bluetooth, disconnect
and reconnect to the device.

•

Make sure that the USB port power supply is providing enough
power. Laptops or hubs may not be able to supply sufficient power.

•

Remove the scan engine from the USB port, and then re-connect
the scan engine.

•

Connect the scan engine to a different port.

Scan engine does not
appear in the device
manager

•

Try the possible solutions for the previous problem.

•

Open the COM port with the communication tool.

Error beep sounds and there
is no output after reading a
barcode

•

On the PC, open Device Manager and confirm the COM port
number. For help, see

“Connection Confirm” on page 29

•

Close and re-open the communication tool. For help, see the
communication tool documentation.

•

Reboot the PC.

Characters are out of order

Make sure that the code to be read matches to the character code of
the communication tool.

Line-break is doubled

Check the line-break setting of the communication tool.

4.3

USB-HID

When using the USB-HID interface, make sure the 12-pin FFC cable is connected to USB
signals.

Caution: UART is a standard factory default setting. If the host is using a UART
connection circuit, communication will fail

Scan

Engine

USB-COM

Communication

Output to focused application

as character information

Windows PC

Содержание MDI-4000 Series












































































































































Результаты поиска

Содержание MDI-4000 Series

Отзывы:

Opticon MDI-4000 Series, Руководство по последовательному интерфейсу, Страница: 43 / 139

Результаты поиска

Содержание MDI-4000 Series

Отзывы: