manualshive.com logo in svg

Opticon MDI-4000 Series, Руководство по последовательному интерфейсу, Страница: 108 / 139

Поделиться
Скачать
Opticon MDI-4000 Series Скачать руководство пользователя страница 108

MDI-4000 Series Serial Interface Manual 

 

 

 

96 

8.3.6

 

Detection Mode 

Lets you determine which mode to use to detect a barcode.  

•

  Green aiming detection: A barcode is detected when it falls within the green aiming light. 

Use this mode to scan barcodes indoors. In brighter environments, the scan engine may 
have difficulty detecting barcodes using this mode. 

•

  Warm white illumination detection: A barcode is detected when it falls within the range of 

the warm white light. Use this mode to scan barcodes in dark environments. 

•

  No illumination detection: A barcode is detected without any illumination from the scan 

engine. This mode uses the least amount of power, but the effectiveness to detect 
barcodes may also be reduced. Use this mode to scan barcodes in well-lit areas.  

Detection Mode Commands 

Command 

Description 

Default 

[DDG 

Green aiming detection  

✓

 

[DDH 

Warm white illumination detection 

 

[DDI 

No illumination detection 

 

 

8.4

 

Illumination and Aiming 

You can enable or disable warm white illumination and green LED aiming. 

8.4.1

 

Reading LED Illumination 

You can enable or disable LED illumination, select an illumination method, and set illumination 
brightness. Configuring these settings can be helpful to reduce specular reflection and increase 
barcode scanning performance. 

LED Illumination Mode Commands 

Command 

Description 

Default 

[D39 

Enable: Improves reading performance, in general. 

 

[D3A 

Disable: Improves reading performance for barcodes displayed on LCD 
screens. 

 

[D3B 

Automatic switching: Alternates the floodlight between ON and OFF. The 
scan engine memorizes the illumination in which a barcode was read 
successfully and uses this mode to scan the next barcode. Use this mode 
in environments where specular reflection is likely to occur. 

 

[D3Q 

Prevent specular reflection: Disables illumination only when specular 
reflection occurs. 

✓

 

 

LED Illumination Brightness Commands 

Command 

Description 

Default 

[DDB 

Standard brightness 

✓

 

[DDC 

Low brightness 

 

 

 

 

Содержание MDI-4000 Series












































































































































Отзывы:

Нет отзывов