manualshive.com logo in svg

Omron CVM1-CLK21, Руководство по эксплуатации

Поделиться
Скачать
Omron CVM1-CLK21 Скачать руководство пользователя страница 236

220

Troubleshooting Using Indicators

Section 9-1

Troubleshooting with LNK and M/A Indicators

Data Link Cannot be 
Started

The following table describes the LNK and M/A indicators at the startup node
and their use in troubleshooting when a data link cannot be started.

Starting a data link depends on the Controller Link Unit operating normally
and participating in the Network. Refer to Troubleshooting with RUN, ERC,
ERH and INS Indicators earlier in this section and check Unit operation before
using the following table. 

Lit

---

---

Not lit Terminating resistance is 

not set correctly. (Wired 
Unit)

Turn ON the terminating 
resistance at the nodes at 
both ends of the Network 
and turn it OFF at all other 
nodes.

Cables are not connected 
correctly.

Check the cable connec-
tions are reconnect cor-
rectly.

The node address is larger 
than the maximum node 
address set for the network 
parameters.

Either reset the maximum 
node address using the 
Controller Link Support 
Software or reset the node 
address to below the maxi-
mum.

No other nodes exist.

Make sure that 2 or more 
nodes exist within the Net-
work.

No nodes have been set as 
polling nodes.

Refer to 8-1-2 Setting the 
Polling and Polled Nodes 
and set at least one polling 
node. (Controller Link 
Units should normally be 
set as polling nodes.)

The set baud rate is differ-
ent to other nodes (Wired 
Unit).

Refer to Section SEC-
TION 4 Preparations for 
Communications and reset 
the baud rate.

Indicators

Probable cause

Probable remedy

RUN

ERC

ERH

INS

Indicators

Probable cause

Probable remedy

LNK

M/A

Lit

---

Data link operating normally.

---

Flashing

---

There is an error in the data 
link tables.

When the ERH indicator is 
flashing, remake and set the 
data link tables.

When manual setting is used, 
either data link tables have not 
been created for the startup 
node or there is an error in the 
data link tables.

Refer to 5-2-2 Manual Setting 
and set data link tables for the 
startup node.

When automatic setting is 
used, either the data link 
parameters for the startup 
node have not been set or 
there is an error in the data link 
tables.

Refer to 5-2-4 Automatic Set-
ting: “Select All” and set the 
automatic parameters for start-
ing the data links.

Not lit

Lit

Manually set data links are 
already operating on the same 
Network.

Stop the manually set data 
links that are operating and 
restart the data links.

Содержание CVM1-CLK21






















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды