manualshive.com logo in svg

Omron CVM1-CLK21, Руководство по эксплуатации

Поделиться
Скачать
Omron CVM1-CLK21 Скачать руководство пользователя страница 196

180

Remote Programming and Monitoring

Section 7-2

7-2

Remote Programming and Monitoring

A remote PC can be programmed and monitored across a network from a
Programming Device connected to a PC.

7-2-1

Local Networks

SYSMAC Support Software and CV Support Software

A Programming Device connected to a C200HX/HG/HE, CVM1, or CV-series
CPU Unit can program and monitor a C200HX/HG/HE, CVM1, or CV-series
PC on the same network. Programming and monitoring are possible, how-
ever, only for the same type of CPU Unit as the one to which the Programming
Device is connected. For example, if the Programming Device is connected to
a CVM1 or CV-series PC, you can only program and monitor CVM1 or CV-
series PCs on the network.

CX-Programmer

A CX-Programmer connected to a CS/CJ-series, C200HX/HG/HE, CVM1,
CV-series, or CQM1H CPU Unit can program and monitor a CPU Unit on the
same network. Programming and monitoring are possible, including CPU

SYSMAC Support 
Software

Programming Device

Programming 
and monitoring

SYSMAC Support 
Software (CVM1 only) 
or 
CV Support Software

Note

   A factory automation node computer cannot remotely program or 

monitor. The node can only monitor Controller Link Network status.

Controller Link Network

C200HX/HG/HE

Controller Link Network

Programming Device

Programming 
and monitoring

CVM1, or CV-series PC

CVM1, or CV-series PC

Controller Link 
Support Software

C200HX/HG/HE

Содержание CVM1-CLK21






















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды