Omnia 3 Скачать руководство пользователя страница 94

Страница: 94 / 98

, the following messages will be transmitted next on the RS-232 port,

ot up:

output

tput

In t

rce, these “Audio failure” messages are normal. Note that the Omnia's audio

failu

FS, and the signal must remain at or below that level in order for the silence

dete

s possible to see these messages during normal programming if the audio input

leve

5dBFS and remains there until the audio fail algorithm times out.

App

after audio has been restored to levels above –37.5dBFS, the following messages

will

nput

ght input

Not

s but no audio

Input

failure message. This

mea

pplied audio at its Inputs, but that there is no output from the DSP chain.

From

flow, the Input meters follow the input level adjustment controls (Input Menu).

This

to the Input Audio Failure comes from.

Dia

r Messages

In t

enti

Audio Failure Alarm

If no audio is applied to the Omnia

approximately twenty seconds after bo

Flr : Audio failure: left input
Flr : Audio failure: right inpu
Flr : Audio failure: left
Flr : Audio failure: right ou

he absence of an audio sou

re trigger level is –37.5dB

ct algorithm to time out. It i

l happens to fall below –37.

dio Restoration Alarm

roximately five seconds

be seen:

Flr : Audio restored: left i
Flr : Audio restored: ri
Flr : Audio restored: left output
Flr : Audio restored: right output

e that it is possible for there to be audio

Output

failure message

ns that the unit is detecting a

the perspective of signal

is also where the input

gnostic and Erro

he event that you need to contact Telos / Omnia Customer Support for assistance, please see the section

tled Obtaining Service on Page 97 for contact information.

The

es will appear on the front panel screen:

e As Failed.

r when trying to save a new preset while there are already 50 presets (including

the rear-panel PCMCIA card.

Cause:

Too many presets are saved to the rear-panel software card.

Resolution:

Delete a preset or two and then try the save operation again.

The following messages will only appear on the rear panel RS-232 Serial Port. See page 92 for instructions on

how to access the serial port messages.

Work: Insert card to continue!!!

Description:

The operating system cannot see the rear-panel PCMCIA memory card.

Cause:

The rear-panel PCMCIA card is missing or not fully seated.

Resolution:

Turn the power off and make sure that the card is fully inserted into the

top

card slot with the large

Omnia label facing up and the version number sticker facing down. The PC Card is keyed to prevent improper
insertion. Gently

following error messag

Insufficient Memory! Sav

rror will occu

Description:

This e

factory presets) on

press the card into the slot until the black release button, to the right of the card, pops out about

1/2” [12.70 mm]. This indicates the card is properly seated in the PCMCIA slot. If the card is properly seated and
this error still appears, contact Telos / Omnia Customer Support for assistance.

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды