Omnia 3 Скачать руководство пользователя страница 28

Страница: 28 / 98

User presets saved to the PC card are not affected but the default preset is reset to the first factory preset shown

in the list.

Load From Card:

Loads previously saved system parameters from the PC Card.

Save to Card:

Saves system parameters to the PC card. This makes a “copy” of the system configuration that

normally resides in the nonvolatile RAM within the Omnia-3, storing it on the PC Card. This simplifies getting

back to a previous state after numerous system adjustments have been made, but you want to return.

Card Maintenance

Erase User Data:

Choose this selection when you want to erase all

user

information on the PC Card, including

user presets, saved system settings, dayparts, and trigger scripts. When this function is selected, the PC Card is

restored to the initial factory condition, and only the factory presets are available. Before this function is

executed, a pop-up screen will ask for confirmation. Follow the instructions presented on the screen to confirm

erasure of the card.

Daypart Table

Sub-menus in this menu allow viewing and setup of dayparts. These sub-menus are:

Show All:

Displays all of the currently defined dayparts through a series of dialog boxes.

Add Part:

Permits the creation of dayparts. Using various screens, you can select the start day and time, the end

time, and preset. The system will warn the user if the daypart being added overlaps one of the dayparts already

defined.

Note:

You can cancel the

Add Part

operation at any time by selecting the

Cancel

option on any of the daypart

Add Part

screens.

Modify Part:

Permits editing of dayparts already created. The system prompts the user to select one of the

currently defined dayparts, and then displays the same sequence that the user sees when doing an

Add Part

allowing you to edit the daypart. The user can then change the start day and time, end time, or preset associated

with the daypart being edited.

Remove Part:

Permits removal of a daypart. The system prompts the user to select one of the currently defined

dayparts, and then prompts the user with a

Continue To Delete?

dialog with a

Yes/No

option. If the user selects

Yes

, the selected daypart is deleted.

Load from Card:

Retrieves daypart data stored on the PCMCIA card. This operation will restore any dayparts

that were previously saved to the card with the

Save to Card

operation, described below.

Save to Card:

Backs up daypart information onto the PCMCIA card (for safety and sharing with others). It

saves all of the currently defined dayparts and the daypart state to the Omnia-3 PC card. These settings can be

loaded later by selecting the

Load from Card

option.

Current State [Enabled/Disabled]:

Activates or deactivates the use of created dayparts. If

Enabled

, then the

system will automatically change presets as specified by any of the dayparts defined. If

Disabled

, then the

system will not use any of the dayparts defined.

Security

This menu allows configuration of all Omnia security features, such as password access, screen locking, and

remote access control. There are six sub-menus:

Lock Unit, Login, Lock Password, Engineer Password,

Enable Remote

and

Disable Remote.

Lock Unit:

Immediately

locks the front panel controls and display. A dialog box is presented for password

entry to unlock the unit. Either the normal mode or engineer mode password can be used to unlock the unit.

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды