Omnia 3 Скачать руководство пользователя страница 27

Страница: 27 / 98

Tilt EQ (Omnia-3am only)

See

Omnia-3am System Adjustments

in Chapter 5 for full details.

Tilt Frequency (Omnia-3am only)

See

Omnia-3am System Adjustments

in Chapter 5 for full details.

LPF Frequency (Omnia-3am only)

See

Omnia-3am System Adjustments

in Chapter 5 for full details.

HP Filter (Omnia-3am only)

See

Omnia-3am System Adjustments

in Chapter 5 for full details.

LPF Frequency (Omnia-3net/drm only)

See

Omnia-3net/drm System Adjustments

in Chapter 6 for full details.

Stereo Generator (Omnia-3fm Turbo only)

Six parameters are set under this sub-menu:

SCA Level

Composite 1

Composite 2

Pilot Level

Phase Adjust

and

Separation

See

Omnia-3fm Turbo System Adjustments

chapter 4 for full details.

Display

Two parameters are set under this sub-menu: Contrast and Backlight.

Contrast

adjusts the brightness difference between the lightest and darkest segments in the front panel display.

Note that if this setting is mis-adjusted the display will “disappear.”

Backlight

adjusts the LCD’s backlight to compensate for room brightness.

Utility

There are nine parameters or sub-menus reached through this menu item:

About

Preset

System

Attributes

Card Maintenance

Daypart Table

Security

Set Time

Set Date

and

Control Port Baud

About

The first thing displayed when you click on

About

is the Omnia factory telephone number in Cleveland! To

display the currently running software versions, click

. The Style and Release version will be displayed.

Click

again and the Bios, display and Loadset versions are displayed. Clicking

again brings up the

Preset

This sub-menu has two parameters:

Delete

and

Rename.

Select

Delete

to permanently delete a User Preset

from the PC Card. A selection box will be displayed allowing you to choose a preset for deletion. Once a

choice is made, a confirmation box is displayed. The preset will not be deleted until “OK” is selected from the

confirmation box. Select

Rename

to change the name of an existing User Preset. A selection box will be

displayed allowing you to choose a preset to be renamed. Once a choice is made, a naming box is displayed to

enter the new name for the preset. This works as described above in “Audio Processing”: “Save to Card as”.

System Attributes

There are three parameters under this sub-menu item:

Load Defaults

Load From Card

and

Save to Card

Load Defaults:

Reloads all of the factory default system parameters into the system. System parameters are

anything that is not saved with the processing preset, such as input and output levels, and RS-232 baud rate.

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды