Omnia 3 Скачать руководство пользователя страница 8

Страница: 8 / 98

76 kHz Suppression: > 80 dB (referenced to 100% modulation).

57 kHz (RDS/RBDS) Protection: better than -50 dB.

Connectors: Two EMI suppressed female BNC, floating over chassis

ground.

Maximum Load Capacitance: 5nF (at 10 ohms source impedance).

Maximum cable length: 100 feet/30 meters RG-58A/U.

Analog I/O

Analog Audio Input:

Configuration: Left/Right Discrete Stereo. Electronically balanced, floating and

symmetrical.

Input impedance: 10k ohms resistive, electronically balanced.

Maximum

Input

Level:

+24

dBu.

Nominal Input Level: +4 dBu when the Input Level Control is set to 0.0 dB.

A/D Conversion:

Crystal Semiconductor CS5360, 24 bit 128x over-sampled delta sigma

converter

with

linear-phase

anti-aliasing filter. Pre-ADC anti-alias filter,

with high-pass filter at <10 Hz.

Connectors:

Two EMI-suppressed XLR female. Pin 1 chassis ground, and Pin 2 is “hot”.

Analog Audio Output:

Configuration: Left/Right Discrete Stereo. Electronically balanced,

Source Impedance: 20 ohms, electronically balanced and floating.

Load Impedance: 600 ohms or greater, balanced or unbalanced.

Output Level (100% peak modulation): Adjustable from -2 dBu to +22

dBu peak, into 600 ohms or greater load, software-adjustable.

D/A Conversion:

Crystal Semiconductor CS4390 24 bit, 128x over-sampled.

Connectors:

Two, EMI-suppressed XLR-male. Pin 1 chassis ground, Pin 2 “Hot”.

Digital I/O

Digital Audio Input:

Configuration: Stereo per AES/EBU standard, CS8420 Digital Audio

Transceiver with 24 bit resolution, software selection of stereo, mono

from left, mono from right or mono from sum. Automatically accepts

and locks to input sample rates between 12 and 50 kHz.

Connector:

XLR-female, EMI-suppressed. Pin 1 chassis ground, pins 2 and 3

transformer

isolated,

balanced,

and floating – AES3 standard 110 ohm

impedance.

Digital Audio Output:

Stereo per AES3 standard. Output can be configured in software for flat

or pre-emphasized response at 50 or 75 microseconds.

Output sample rate fixed at 48 kHz.

Connector:

XLR-male, EMI-suppressed. Pin 1 chassis ground, pins 2

and 3 transformer isolated, balanced, and floating. Standard AES3

specified 110 ohm source impedance.

Digital Output Level: -22.0 to 0.0 dBFS software adjustable.

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды