Omnia 3 Скачать руководство пользователя страница 73

Страница: 73 / 98

r direct serial connection at the time, it will be

Omnia Remote and

control session is disconnected,

red. Man

ired to restart

y lost. Preset

e Daypart Scheduler is typically used to change a Preset at a set day and time. But, when a script is added to

x is checked. The

Preset

check box can be used to disable

hen the daypart executes. Un-check this box when you want a daypart to

ion is stored and retrieved in the

d in any way from the front panel.

•

If Omnia Remote Control is connected by a modem o

disconnected and manual intervention will be required to reconnect.

•

If Omnia Remote Control is connected by Ethernet at the time, the meters on

Omnia front panel will freeze. However, when the Omnia Remote

normal Omnia front panel operation will be resto

ual intervention will be requ

Omnia Remote Control.

•

If you have not saved the System or Trigger Script settings, they may be permanentl

adjustments are saved in NVRAM and are not lost at power down.

nitiating Scripts via the Daypart Scheduler

the Daypart table, the script can dynamically change one or multiple attributes when the Daypart is executed. A

script for use by the Daypart functions is written using the special script editor built into the New or Modify

Schedule window in the Remote Software (Only) and the syntax is the same as for the Trigger Scripts described

in the previous section.

The Daypart Scripts editor is accessed from the New or Modify Schedule window by highlighting and clicking

on the

Scripts

button. There are also

Test

buttons on the page to force the Omnia-3 to immediately run the

current Start Script or End Script.

At the bottom of each editor window is a check box to enable or disable the use of the script. A script may be

entered but will not be executed until the enable bo

the action of changing the preset w

execute

only

the given scripts and

not

change the preset. A daypart can actually be disabled completely by un-

checking the

Preset

Enable Start Script Execution

and

Enable End Script Execution

check boxes.

Start scripts execute at the beginning of a daypart, before making a preset change (if any). End scripts execute at

the end of the daypart, after making any preset changes. The script informat

same means as other daypart information.

Dayparts can still be selected, etc. from the Omnia-3 front panel interface. However, dayparts with scripts

cannot be modifie

Note:

Remember not to include any commands that may potentially prompt the user, since a user may not be at

the Omnia-3 when the commands are executed.

Note:

The remote control application does not have to be connected in order for the scripts to execute.

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды