Omnia 3 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 98

background image

WARNING --

This equipment generates, uses, and can radiate radio frequency energy. If not installed

and used in accordance with the instructions in this manual it may cause interference to radio
communications. It has been tested and found to comply with the limits for a Class A computing device
(pursuant to subpart J of Part 15 FCC Rules), designed to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference, at which case, the user, at his own expense, will be required to take
whatever measures may be required to correct the interference.

See the following page for additional information.

CANADA WARNING

–

This digital apparatus does not exceed the Class A limits for radio noise

emissions set out in the Radio Interference Regulations of the Canadian Department of Communications.
Le present appareil numerique n'emet pas de bruits radioelectriques depassant les limits applicables aux
brouillage radioelectrique edicte par le ministere des Communications de Canada.

CE CONFORMANCE –

This device complies with the requirements of the EEC Council Directives:

93/68/EEC (CE Marking); 73/23/EEC (Safety – low voltage directive); 89/336/EEC (electromagnetic
compatibility). Conformity is declared to those standards: EN50081-1, EN50082-1.

LITHIUM BATTERY CAUTION --

Danger of explosion if the internal battery is replaced

incorrectly. Replace only with same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.

USE OF SHIELDED CABLING --

To conform to the CE requirements for High Frequency

radiation, shielded cables must be used for all audio and data connections. For analog and
digital connections, the cable shield MUST be connected to the XLR-type connector shell,
which is at chassis ground potential!

5

«
...
3
4
5
6
7
...
»

Содержание 3



































































































Отзывы:

Нет отзывов

Похожие инструкции для 3

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: Danfoss Страницы: 61

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Бренд: IOtech Страницы: 16

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

Marconi OMS 1200

Бренд: Ericsson Страницы: 136

Бренд: PaloAlto Networks Страницы: 28

Бренд: PairGain Страницы: 80

Бренд: FiberHome Страницы: 2

CloudGen Firewall

Бренд: Barracuda Страницы: 8

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренд: Moxa Technologies Страницы: 8

CamCon FCS-4000

Бренд: LevelOne Страницы: 94

Бренд: Dataprobe Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды