Omnia 3 Скачать руководство пользователя страница 97

Страница: 97 / 98

onday through Friday between

9:00 A.M. and 6:00 P.M., Eastern Time. If outside the U.S.A., see below.

a small

oblems

•

All units being returned to for service MUST have a Return Authorization (RA) number assigned to them first.

number will experience delays in service.

ing carton. For best treatment, shipping the Omnia in its original factory

anty!

neer

the necessary arrangements

e has a wide variety of information that may be useful for product support, applications

information, software updates, etc. The URL is:

http://www.omniaaudio.com./

Obtaining Service

•

Omnia Customer Support personnel are available in Cleveland, Ohio, USA, M

•

Before contacting Omnia Customer Support, please have the serial number of the unit (located on
barcode sticker on the rear panel in this format: 4300XXYYYY) and a description of the symptoms/pr
ready for the technician.

Units that are returned without a RA

•

Return the Omnia in its original shipp
box protects it as well as possible. Damage caused by improper packaging is not covered under your warr

•

Loaner units are usually available on a first come, first served basis. Your Omnia Customer Support engi
will assist you with

Note: To ensure prompt service, the Return Authorization number must be written
prominently on or near the shipping label on the box!

Via the World Wide Web

The Omnia Web sit

Via E-Mail

The customer service e-mail address for Omnia is: [email protected].

Via Phone & Mail (USA and non-European Countries)

Customer service is available by telephone, Monday – Friday between 9:00 A.M. and 6:00 P.M., USA Eastern

time zone.

Omnia Europe

Johannistra

e 6

Phone:

+1.216.241.7225

Fax:

+1.216. 241.4103

Shipping Information:

Omnia Customer Service

2101

Superior

Avenue

Cleveland,

Ohio

44114

USA

Via Phone & Mail for Europe

Service is available from the Omnia Europe office in Freising, Germany.

Phone:

+49 8161 42467

Fax:

+49 8161 42402

Shipping Information: *

D-85354

Freising,

Germany

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды