Omnia 3 Скачать руководство пользователя страница 63

Страница: 63 / 98

Technical note: the Omnia 3 Remote Control communicates with the Omnia 3 using a Telnet session on Port

23. If you are unable to communicate with the Omnia through a network firewall, the first thing to check is

whether traffic on port 23 is being permitted.

Enter the password for the unit in the Password box. If nothing is entered, you will be asked for the password at

the time you connect to the remote Omnia. The default passwords for Ethernet remote connections are the same

as the front panel passwords:

Normal: “vito” (all lower case)
Engineer: “tomtom” (all lower case)

The Remote Control software allows multiple connection profiles to be created so that a mix of connection

types (Direct,

nicating with

Note: These connection settings are stored in a small binary file named

located in the same folder

Connecting via Ethernet Network

For Network connections, check the

Connect over Ethernet

box and enter the IP address of the Omnia-3fm

Turbo in the box provided. The TCP/IP address entry format is: xxx.xxx.xxx.xxx. The TCP/IP address of the

Omnia-3 Ethernet hardware interface is set during initial configuration.

Serial, TCP/IP) may be used. This allows the program to easily support commu

different Omnias at different locations, connected by different means.

When all items have been entered, select OK.

connect.dat

as the remote program.

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды

Omnia 3, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 3

Отзывы:

Похожие инструкции для 3

Бренды по названию

Популярные бренды