Omnia 3 Скачать руководство пользователя страница 77

Страница: 77 / 98

ss and port number of the Omnia-3. These were

If connecting via Direct Serial or Modem, then select the COM port that you wish to use on your

PC. This COM port should be configured in Windows for the highest baud rate that your PC will

support, but in any case, should be set to at least 57,600 bps.

If connecting via Direct Serial, no other information is required.

If connecting via Modem, in the “Phone #” box, enter the telephone number of the modem that is

connected to the Omnia at the remote site. Any

If connecting via network, enter he IP addre

configured during installation of the optional Ethernet interface. The format is

xxx.xxx.xxx.xxx:pppp.

characters present in the “Phone #” box signal the

Omnia Remote program to attempt a connection via modem!

Click on

to save all the changes and close the Edit Connection dialog.

If you need to use a Modem Initialization string, check the

“Custom Initialization String”

str

box, and enter

it in the . If you require a modem initialization string and feel more comfortable building the entire connect

string within the “Phone

zation Strings” for more

ide...

Remote Co

Omnia PCMCIA Modem

Before us

Omnia-approved

ing

#” box you may do this. See “Using Custom Modem Initiali

information.

Omnia Remote Control supports a wide variety of Hayes command set compatible modems. If you have

difficulty using your modem, you may call Omnia Customer Support for assistance, but please gather as much

information about your modem as possible before doing so.

On the Omnia S

ntrol Using the Optional

e, ensure that the

PCMCIA modem card is fully inserted into the lower PC Card slot

on the ba

dular telephone

jack. Using a standard RJ-11cable, connect your telephone line to the Omnia modem. Make a note of the

Note:

The modem card can only be safely installed and removed when the Omnia's power is

off

. Only the

port for such non-

e Co

The Omnia s

support the w

ck f the Omnia. Press on the modem card's “XJACK” connector to extend the mo

telephone number corresponding to this line, as you will need it later when you configure the Omnia Remote

Control program.

PCMCIA modem card supplied by Telos Omnia has been tested and approved by Telos Omnia. We cannot

ensure correct operation of any other modem card with the Omnia-3, nor can we provide sup

approved cards.

mot

ntrol Using a External Hayes Compatible Modem

upports nearly every Hayes command set compatible modem available. Please note that in order to

idest possible variety of externally connected serial devices the Omnia-3's RS-232 port does not

ware or software handshaking. This is of no c

support hard

oncern, and we are aware of no instances where this

has prevented an externally connected modem from operating properly. The externally connected modem will

need

auto

Because the

-detect one of the Omnia's three rear panel serial port's baud rates (9,600, 19200, and 57,600).

Omnia and the modem are both DCE devices, you will need to use a crossover (null modem) cable

between them

e Co

When a com

rather than di

serial cable w

the computer end. You should verify the exact type required by your computer.

mot

ntrol Using a Direct RS-232 Connection for Local Communications

puter can be located near the Omnia-3, it may be convenient to use a direct serial cable connection

al up. Use a standard, straight-through serial cable -- null-modem cables will not work!

A typical

ill need a DB-25 male connector for the Omnia-3 end, and probably a DB-9 female connector

Содержание 3



































































































Результаты поиска

Содержание 3

Отзывы:

Omnia 3, Инструкция по установке и эксплуатации, Страница: 77 / 98

Результаты поиска

Содержание 3

Отзывы: