Oki OKIOFFICE 84, Руководство пользователя

Страница: 65 / 96

User’s Guide 65
Press the
ô
YES key and all pages of your document that were
scanned into memory will be sent. After the scanned pages have
been sent, the display changes to:
R E L O A D D O C U M E N T R E L O A D D O C U M E N T
R E L O A D D O C U M E N T R E L O A D D O C U M E N T
R E L O A D D O C U M E N T
After you have reloaded your document, you can send the
remaining pages of your document with another fax
transmission.
If this function is set to on and you DO NOT press the
NO
õ
key
within one minute of the message
SEND SCANNED PAGES
,
your machine automatically starts sending the scanned pages.
If this function is set to off and you DO NOT press the
NO
õ
key
within one minute, your scanned pages are cleared from the
memory.
Available settings for this function are on and off.
24:CONTINUOUS TONE 24:CONTINUOUS TONE
24:CONTINUOUS TONE 24:CONTINUOUS TONE
24:CONTINUOUS TONE
- With this function on, your
machine will emit a continuous tone when receiving a
transmission. Pressing the
STOP
key turns off the tone. Set this
function to off and your machine will emit a short beep after
receiving a fax message. Available settings are on and off.
25:INSTANT DIALLING 25:INSTANT DIALLING
25:INSTANT DIALLING 25:INSTANT DIALLING
25:INSTANT DIALLING
- Set this function to start
reading documents upon call origination when transmitting to
a single location. Available settings are on and off.
26:RESTRICT ACCESS 26:RESTRICT ACCESS
26:RESTRICT ACCESS 26:RESTRICT ACCESS 26:RESTRICT ACCESS - Select whether or not you want
restricted access. Turning on this function renders your restricted
ID registration active. Available settings are on and off.
27:WIDTH REDUCTION 27:WIDTH REDUCTION 27:WIDTH REDUCTION 27:WIDTH REDUCTION 27:WIDTH REDUCTION
- Turning this function on enables
you to print received data at a slightly reduced width. Available
settings are on and off.
28:ONE TOUCH PARAM. 28:ONE TOUCH PARAM. 28:ONE TOUCH PARAM. 28:ONE TOUCH PARAM. 28:ONE TOUCH PARAM.
- This function allows you to
make changes to the communications settings for a specific
One Touch key, without changing the normal communication
settings used by your machine. For instructions on changing
One Touch Parameters settings for a One Touch key, see One
Touch Parameters in Dial Directories.
Changing User Function Settings
1. Press the
SELECT FUNCTION
key.
2. Press the USER PROG One Touch key. The display shows:
1 : F U N C . P R O G R A M M I N G 1 : F U N C . P R O G R A M M I N G
1 : F U N C . P R O G R A M M I N G 1 : F U N C . P R O G R A M M I N G
1 : F U N C . P R O G R A M M I N G
Y E S ( Y E S (
Y E S ( Y E S ( Y E S (
ß ß ß ß ß
) N O ( ) N O (
) N O ( ) N O ( ) N O (
à à à à à
/ 1 - 7 ) / 1 - 7 )
/ 1 - 7 ) / 1 - 7 ) / 1 - 7 )
3. Press the
ô
YES
key. The display shows:
F U N C T I O N N O . [ ] F U N C T I O N N O . [ ] F U N C T I O N N O . [ ] F U N C T I O N N O . [ ] F U N C T I O N N O . [ ]
E N T E R 0 1 - 2 8 E N T E R 0 1 - 2 8 E N T E R 0 1 - 2 8 E N T E R 0 1 - 2 8 E N T E R 0 1 - 2 8
4. Using the numeric keypad, enter the 2-digit number of the
function you want to change. This display then shows the
name of the selected function.
5. Press the
NO
õ
key to cycle through the settings for the user
function, then press the
ô
YES key to confirm your selection.
The name of the next user function appears in the display.
6. To select another user function, press the STOP key and
return to step 4.