Ohmeda Ohio Care Plus Скачать руководство пользователя страница 72

Страница: 72 / 84

A-2

Appendix

A-2

6600-0239-000 100

Performance specifications

Patient temperature measurement

Range Displayed: +22 to 42°C (71.6 to 107.6°F)

Accuracy*: ± 0.3°C (± 0.5°F) within a range of 30-42°C

Resolution: ± 0.1°C or °F

Probe Model Numbers: LA003, LA005 (disposable)

Probe Interchangeability: ± 0.1°C (± 0.2°F)

Air temperature measurement

Range Displayed: 5 to 50°C (41.0 to 122.0°F)

Resolution: ± 0.1°C or °F

Accuracy*: Varies over temperature range

Temperature Range

Accuracy

5 to 22°C (41-71.6°F)

± 0.5°C (0.9°F)

22.0 to 42.0°C (71.6-107.6°F)

± 0.3°C (0.5°F)

42.0 to 50.0°C (107.6-122.0°F)

± 0.5°C (0.9°F)

Control temperature ranges

Patient Control Mode: 35.0 to 37.0°C (95.0 to 98.6°F), up to 37.5°C (99.5°F) with

internal adjustment

Air Control Mode: 20.0 to 37.0°C (68.0 to 98.6°F), up to 39.0°C (102.2°F) with

control panel Override switch.

Thermal performance

Temperature Rise Time*: Less than or equal to 20 min

Temperature Variability*: 0.2°C (0.4°F)

Temperature Overshoot*: Less than or equal to 0.8°C (1.4°F)

Note: * These terms are defined in the Glossary.

Alarms

Indicator and Nonsilenceable Audio Alarm

Power Failure

Indicator and Silenceable Single Tone Alarm

Difference between patient temperature and patient control temperature exceeds

1.0°C patient control mode (can be adjusted to 0.5°C).

Air temperature is 1.5°C above or 3.0°C below air control temperature (air control mode;

Disabled for 15 minutes after control temperature change and for 30 minutes

on power up).

Indicator, Silenceable Two Tone Alarm and Heater Shutdown

Air temperature sensor disconnected (both modes)

Patient probe disconnected or malfunctioning (patient control mode)

Air circulation system failure

Patient temperature > 42.0°C or < 30.0°C

Air temperature > 38.0°C (air control mode w/o Override)

Air temperature > 40.0°C (patient control mode or air control mode with Override)

Содержание Ohio Care Plus





















































































Результаты поиска

Содержание Ohio Care Plus

Отзывы:

Бренды по названию

Популярные бренды

Ohmeda Ohio Care Plus, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание Ohio Care Plus

Отзывы:

Бренды по названию

Популярные бренды