OHAUS 7000 Series Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 107

background image

CHAPTER 2 TROUBLESHOOTING

7000 Series T72XW Indicators Service Manual

2-7

Ohaus Corporation www.ohaus.com

Symptom

Suggestion

No serial port
communications

Use serial diagnostics section of Maintenance
block of setup to determine if the problem is
internal or external to the terminal.

Contact service representative.

Discrete inputs or
outputs don’t
operate

Use the discrete input and output diagnostics
section of the Maintenance block of setup or the
DIO status display on the system line to determine
if the problem is internal or external to the terminal.

Contact service representative.

2.5 Internal Diagnostics

The T72XW terminal provides several internal diagnostic tools that are accessible in setup
mode.These tests are intended to assist in diagnosing whether a problem is internal or external
to the terminal.

To access these tools, enter the Operator menu then the

SETUP

mode and navigate to the

Maintenance menu. Open the Maintenance block then the Diagnostic block.

Each of the diagnostic items is shown in the menu.

The following diagnostic tests are included:

2.5.1 Display Test

When the display test is run, the terminal will display all dots on for approximately 4 seconds
then all dots off for another 4 seconds. This cycle will repeat continuously until the

LEFT

navigation key is pressed to exit.

Note: All dots are also illuminated on the display during the power up sequence.

«
...
38
39
40
41
42
...
»

Содержание 7000 Series












































































































Отзывы:

Нет отзывов

Похожие инструкции для 7000 Series

Бренд: Keithley Страницы: 201

Бренд: Waltron Страницы: 11

Бренд: Labom Страницы: 6

Бренд: Labom Страницы: 5

Бренд: IEI Technology Страницы: 85

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: Lasertec Страницы: 21

Бренд: KROHNE Страницы: 56

Бренд: Power Measurement Страницы: 20

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Бренд: LORECa Hearing Instrument Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды