OHAUS 7000 Series Скачать руководство пользователя страница 76

Страница: 76 / 107

APPENDIX A GEOGRAPHICAL ADJUSTMENT VALUES

Ohaus Corporation www.ohaus.com

B-6

7000 Series T72XW Indicators Service Manual

– Line Feed (0Axh)

Comment

– the <CR> and <LF> characters will not be shown in this description.

B.11 Format of Error Message

There are three different error messages.

The identification always comprises two characters:

– Syntax error

The terminal has not recognized the received command.

– Transmission error

The terminal has received a “faulty” command, such as a parity error.

– Logical error

The terminal cannot execute the received command.

– Carriage return (0Dxh)

– Line Feed (0Axh)

Comment

– the <CR> and <LF> characters will not be shown in this description.

Tips for the Programmer

Tips for creating a robust communication with the terminal using the SICS protocol include:

B.12 Command and Response

Improve the dependability of application software by having the program evaluate the response
of the terminal to a command.The response is the acknowledgment that the terminal has
received the command.

Содержание 7000 Series












































































































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

OHAUS 7000 Series, Руководство по обслуживанию

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды