background image

TABLE OF CONTENTS 

7000 Series T72XW Indicators Service Manual 

Ohaus Corporation  www.ohaus.com 

CHAPTER 1  GETTING STARTED 

(Continue)

 

Page No. 

 1.10.22 Reset .............................................................................................................. 1-25 

CHAPTER 2  TROUBLESHOOTING 

2.1 

Introduction ..............................................................................................................2-1 

2.2 

Diagnostic Guide ......................................................................................................2-1 

2.3 

Error Codes And Error Message ..............................................................................2-3 

2.4 

troubleshooting ........................................................................................................2-5 

 2.4.1    Blank Display ....................................................................................................2-5 
 2.4.2    Power Test .......................................................................................................2-5 
 2.4.3    Problem Diagnosis ...........................................................................................2-5 

2.5 

Internal Diagnostics ..................................................................................................2-7 

 2.5.1    Display Test .......................................................................................................2-7 
 2.5.2    Keyboard Test ...................................................................................................2-8 

2.6 

Scale Diagnostics ....................................................................................................2-8 

2.7 

Serial Test ................................................................................................................2-8 

2.8 

Discrete I/O Test .................................................................................................... 2-10 

2.9 

System Backup and Restore .................................................................................. 2-11 

2.10  Backup to SD Memory Card ................................................................................... 2-12 
2.11  Restore From SD Memory Card ............................................................................. 2-12 
2.12  Master Reset .......................................................................................................... 2-13 
2.13  Updating Firmware ................................................................................................. 2-14 

CHAPTER 3 MAINTENANCE PROCEDURES 

3.1 

Preventive Maintenance ...........................................................................................3-1 

3.1.1  Cleaning and Maintenance ...............................................................................3-1 

 3.2 

Replace of Major Components .................................................................................3-2 

 3.2.1 

Opening the Enclosure .....................................................................................3-2 

 3.2.2 

Closing the Enclosure .......................................................................................3-3 

 3.2.3 

Main Printed Circuit Board (PCB) Replacement ................................................3-3 

 3.2.4 

Back Light LCD Display Replacement ...............................................................3-5 

 3.2.5 

Membrane Switch Replacement .......................................................................3-6 

3.3 

Wiring Connection ....................................................................................................3-7 

 3.3.1 

Analogue Load Cell Connections ......................................................................3-7 

3.4 

PCB Switch Setting ..................................................................................................3-9 

 3.4.1 

Main PCB Swicthes ..........................................................................................3-9 

3.5 

SD Card Installation ............................................................................................... 3-10 

3.6 

Securing the Enclosure .......................................................................................... 3-11 

CHAPTER 4 PARTS LISTS & DIAGRAMS 

4-1

7000 Series T72XW Indicator: Housing & Internal Parts ..........................................4-2 

Содержание 7000 Series












































































































Отзывы: