OHAUS 7000 Series Скачать руководство пользователя страница 10

Страница: 10 / 107

CHAPTER 1

GETTING STARTED

7000 Series T72XW Indicator Service Manual

1-3

Ohaus Corporation www.ohaus.com

1.5 SPECIFICATIONS

TABLE 1-1. SPECIFICATIONS

T72XW Specifications

Enclosure Type

Stainless steel, configurable as desk top or wall mount enclosure

Dimensions (w



283 mm x 232 mm x 86 mm (11.1 in. x 9.1 in. x 3.4 in.)

Shipping Weight

AC Version: 3.4 kg (7.5 lb)

Environmental Protection

IP66 (comparable to Type 4x)

Operating Environment

The terminal can be operated at temperatures ranging from



10° to 40° C (14° to

104° F) at 10% to 95% relative humidity, non-condensing.

Hazardous Areas

The T72XW terminal cannot be operated in areas classified as Hazardous because
of combustible or explosive atmospheres in those areas.

Power

Operates at 85

–264 VAC, 49–61 Hz and includes a power cord configured for the

country of use.

Power Consumption

Refer to

Error! Reference source not found.

Table 0-1

Values shown are with

internal COM2/DIO option and Ethernet option installed and load cell input loaded
with 8 x 350



load cells.

Display

Backlit 240 x 96 dot graphic LCD including weight display, weight units, gross/net
indication and graphic symbols for motion and center of zero, SmartTrac, operator
prompts and data entry display. Update rate of 12 updates per second.

Basic weight mode: 27 mm (1.1 in) high weight display

Application mode: 20 mm (0.8 in) high weight display

Weight Display

Maximum displayed resolution of 50,000 divisions.

Scale Types

Analog load cells

Number of Cells

From one to ten 350-ohm load cells (2 or 3 mV/V)

Number of Scales

One

Analog/Digital Update Rate

Internal analog: 366 Hz

Load Cell Excitation Voltage

10 VDC

Minimum Sensitivity

0.1 microvolt per increment

Keypad

25 keys; polyester overlay (PET) with polycarbonate display lens

Communications

Serial Interfaces

Standard: One isolated serial port (COM1) RS-232, 300 to 115,200 baud

Optional isolated serial port: (COM2) RS-232/485, 300 to 115,200 baud

Optional USB port: serial port bridge, 300 to 115,200 baud

Ethernet Interface

Optional Ethernet port: 10/100 TCP/IP port

Protocol

Serial Inputs: ASCII commands for CTPZ (Clear, Tare, Print, Zero), SICS (most
level 0 and level 1 commands)

Serial Outputs: Continuous, Extended continuous, Demand (limited formats),

Содержание 7000 Series












































































































Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды

OHAUS 7000 Series, Руководство по обслуживанию

Результаты поиска

Содержание 7000 Series

Отзывы:

Похожие инструкции для 7000 Series

Бренды по названию

Популярные бренды