manualshive.com logo in svg

NSK MEGATORQUE M-ESA-J0002V25, Руководство пользователя

Поделиться
Скачать
NSK MEGATORQUE M-ESA-J0002V25 Скачать руководство пользователя страница 289

— A-22 —

5. Troubleshooting

l

 

When the brake does not perform as intended, check followings.

u

 

Brake is slipping.

1)

Is the friction plate soiled with oil?

2)

Is temperature of the brake too high? (over 100 °C)

3)

Is excessive load applied to the machine?

u

 

Sluggish operation of the brake

1)

Is sufficient voltage being supplied?

2)

Is the friction plate worn out ? (too much gap)

3)

Is brake temperature too high? (over 100 °C)

u

 

The brake does not operate entirely.

1)

Breakage of coil and/or lead wire

2)

Electrical circuit failure

3)

Too much gap of the friction plate because of wear?

4)

Is sufficient voltage being supplied?

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MEGATORQUE M-ESA-J0002V25







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды