manualshive.com logo in svg

NSK MEGATORQUE M-ESA-J0002V25, Руководство пользователя

Поделиться
Скачать
NSK MEGATORQUE M-ESA-J0002V25 Скачать руководство пользователя страница 101

— 7-6 —

7.3.2. “?” Reading Function Command for Set Value

1)

When entering the command, make sure that a colon ( : ) is displayed on the screen.
(If the colon is not displayed, press the enter key once.)

:_

ENT

2)

Enter “?” before inputting the command.
In case of this example, input “JV” after “?”.

:?JV
 JV0.10
:_

ENT

J

V

?

3)

The colon ( : ) is displayed to indicate the system is waiting for next command.

Caution  : When reading out set value, using TS command is recommended.

When using “?” command, make sure to input “?” command before
parameter characters. If not, and pressing  ENT  key after the characters
may change the set value.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MEGATORQUE M-ESA-J0002V25







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды