manualshive.com logo in svg

NSK MEGATORQUE M-ESA-J0002V25, Руководство пользователя

Поделиться
Скачать
NSK MEGATORQUE M-ESA-J0002V25 Скачать руководство пользователя страница 238

— 13-1 —

13. Maintenance

13.1. Precautions

l

 

Back up Motor and Driver Unit

◊

 

We recommend to have a back up Motor and Driver Unit for unexpected shut down of
the system.

l

 

Parameter and program back up

◊

 

For an unexpected shut down of the Driver Unit, all parameters and programs should be
recorded.

◊

 

For your convenience, the list of parameter and program is provided in the last page of this
manual.

l

 

How to replace the Driver Unit.

◊

 

Standard ESA25 Driver Units are interchangeable with each other. It may be replaced
simply by inputting same parameter settings of old Driver Unit.
Following shows reference number of standard ESA25 Driver Unit.

• M-ESA-*****T25

• M-ESA-*****V25

(***** represents Motor number. The Driver Unit to be replaced must have same
number.)

l

 

If your Driver Unit is not standard, refer to the specification documents for interchangeability.

l

 

When replacing the Driver Unit, refer to “Appendix 4: How to Replace ESA25 Driver Unit.”

l

 

ESA25 Driver Unit has EEP-ROM and does not need a battery for memory back up.

(Life of EEP-ROM : approximately 500 000 times of writing on and off.)

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MEGATORQUE M-ESA-J0002V25







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды