manualshive.com logo in svg

NSK MEGATORQUE M-ESA-J0002V25, Руководство пользователя

Поделиться
Скачать
NSK MEGATORQUE M-ESA-J0002V25 Скачать руководство пользователя страница 285

— A-18 —

Appendix 5 : Regeneration Dump Resistor

l

 

Megatorque Motor will function as a generator in the following conditions. This phenomenon is
called regeneration.

◊

 

When decelerating under heavy inertia.

◊

 

When the Motor axis is horizontal, weight of an unbalanced load attached to the    rotor
gives torque load to the Motor.

l

 

Energy generated by the motor will be charged to the main power circuit condenser. If energy is
more than the capacity of the condenser, a dump resistor of the Driver Unit will dissipate overflown
energy.

l

 

However, when the regeneration occurs frequently, the dump register will be overheated due to its
limited capacity. Eventually over-heat alarm will be on and Motor will stop.

* Dump resistor capacity is about 2.5W.

l

 

When an over-heat alarm is detected, following remedies should be taken.

◊

 

Reduce duty cycle

◊

 

Decrease acceleration/deceleration.

◊

 

Lower operation speed.

l

 

If above measures are not feasible, an optional high capacity regenerative dump register is available
from NSK. It will dissipate regeneration energy without loosing speed of Megatorque Motor.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание MEGATORQUE M-ESA-J0002V25







































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды