Novus RHT Climate-DM Series Скачать руководство пользователя страница 29

Страница: 29 / 48

NOVUS AUTOMATION

29/48

USB INTERFACE

The USB interface is used for CONFIGURING or MONITORING the device. For CONFIGURATION, the

NXperience

software should be used,

which offers features for creating, viewing, saving and opening configurations from the device or from files on your computer. The feature for saving

and opening configurations in files makes it possible to transfer configurations between device and make backup copies. For specific models,

NXperience

also allows for updating the controller’s firmware (internal software) via USB interface.

For MONITORING, any supervision (SCADA) or laboratory software may be used that offers support for Modbus RTU communication over a serial

communication port. When connected to a computer USB port,

TEMP

Climate

Transmitter

is recognized as a conventional serial port (COM x). Use

NXperience

or refer to the Device Manager on Windows Control Panel to identify the COM port that was assigned to the transmitter. Refer to the

Modbus memory mapping in the device’s communication manual and its supervision software documentation to perform MONITORING.
Follow the procedure below to use the device’s USB communication:

•

Download

NXperience

from our website and install it on your computer (see chapter NXPERIENCE SOFTWARE). The USB drivers required for

communication will be installed along with the software.

•

Connect the USB cable between the device and the computer. The controller doesn’t need a power supply. The USB will provide enough power

for the communication operation (other device functions may not operate).

•

Launch

NXperience

, configure communication and start device recognition.

The USB interface IS NOT ISOLATED from the retransmission outputs and alarm

outputs. Its purpose is temporary use during CONFIGURATION and

MONITORING periods. For the safety of people and device, it should only be

used with the device fully disconnected from the external power supply inlet. USB

use in any other connection condition is possible, but it requires careful analysis

by the person in charge of installation. For MONITORING for long periods and

with inputs and outputs connected, use of the RS485 interface is recommended,

available or optional in most of our devices.

Содержание RHT Climate-DM Series

















































Результаты поиска

Содержание RHT Climate-DM Series

Отзывы:

Похожие инструкции для RHT Climate-DM Series

Бренды по названию

Популярные бренды

Novus RHT Climate-DM Series, Инструкция по эксплуатации

Результаты поиска

Содержание RHT Climate-DM Series

Отзывы:

Похожие инструкции для RHT Climate-DM Series

Бренды по названию

Популярные бренды