Nortel Meridian M1250 Скачать руководство пользователя страница 50

Страница: 50 / 168

• • • • 44 • • • •

Basic call processing

Extending a call to a busy extension

(with Hold)

To extend a call to a busy extension which is not allowed camp-on, or which already has a call camped
onto it, you can place the caller on hold. You must then reenter the call periodically to see if the extension

is free.

Dial the requested
extension.

The excl. src. indicator
goes on during dialing.

You hear a busy signal
and the D indicator

flashes; the extension is

busy and not allowed
camp-on.

Press RLS dest. The

indicator

goes

off;

the called extension is
released from the console.

If the caller wishes to call

back later, press RLS.

The RLS indicator goes
on; you are free to process

other calls.

If the caller wishes to
wait, press HOLD, then

RLS to end your

connection in the call.

The lpk indicator flashes
slowly. The RLS indicato

goes on; you are free to

process other calls.

Check periodically to see
if the extension is free.
To reenter the call, press

the lpk key beside the
slowly flashing lpk

indicator, then dial the

extension again.

The lpk indicator goes on

steadily.

Содержание Meridian M1250








































































































































































Результаты поиска

Содержание Meridian M1250

Отзывы:

Nortel Meridian M1250, Руководство пользователя, Страница: 50 / 168

Результаты поиска

Содержание Meridian M1250

Отзывы: