Nortel Meridian M1250 Скачать руководство пользователя страница 151

Страница: 151 / 168

• • • • 145 • • • •

Network Attendant Service (NAS)

Extending a call to a busy remote extension

You can route a call to a busy extension at a remote location if camp-on is allowed at the busy end. If the
called extension does not become idle within a set time, you are automatically recalled by the
camped caller.

Note:

If you dial the requested number at the remote location and hear only a busy signal (with no

beep), then a call is already camped onto that extension. If the caller wishes to wait, put the call on
hold. Otherwise, release the call.

You receive a call
intended for a remote
console. Press the lpk
key beside the flashing
ICI key to answer the
call.

The appropriate ICI
indicator is on.

The caller requests an
extension at the remote
location. Dial the
requested extension.

The appropriate ICI
indicators are on. If the
called extension is busy,
you hear a busy signal
followed by a beep; you
are reconnected to the
caller.

If the caller does not
wish to wait, press RLS
dest., then RLS to end
the call.

The RLS indicator goes
on; you are free to process
other calls.

If the caller wishes to be
camped onto the busy
extension, press RLS. [If
recall occurs, either
extend the call again
(step 3b) or end it (step
3a).]

The RLS indicator goes
on; you are free to
process other calls.

Содержание Meridian M1250








































































































































































Результаты поиска

Содержание Meridian M1250

Отзывы:

Nortel Meridian M1250, Руководство пользователя, Страница: 151 / 168

Результаты поиска

Содержание Meridian M1250

Отзывы: