manualshive.com logo in svg

Nortel Meridian M1250, Руководство пользователя, Страница: 127 / 168

Поделиться
Скачать
Nortel Meridian M1250 Скачать руководство пользователя страница 127

• • • • 121 • • • •

Convenience features

Storing a Stored Number Redial number during a call

You can use Stored Number Redial while trying to establish a call (when the other end is ringing or busy), 
or during an established call (when you are talking to someone at the other end). If on an established call,  
go directly to step 3.  (See notes below.)   

Note 1: 

When a call is active on the source and destination side, the destination number is stored. 
If only the source is active, no number is stored.

Note 2:

For internal calls, the dialed digits must result in a busy signal or ringing. If insufficient 
digits or an invalid extension is dialed, the attempt to store the number is rejected and any 
previously stored number is not changed.

Note 3: 

For external calls, if no trunk is available, all digits dialed are stored even though some digits 
may be entered after an overflow or busy signal.

1

Press an idle lpk key.

The lpk indicator goes on.

2

Dial the required 
number.

3

Press snr.

You are on a call.

Содержание Meridian M1250









































































































































































Отзывы:

Нет отзывов