Nortel Meridian M1250 Скачать руководство пользователя страница 2

Страница: 2 / 168

Contents

Introduction 1

Your Meridian 1 attendant console

Dial pad

The Options menu (M2250) (4 line mode)

The Options menu (M1250) (4 line display)

Setting the buzz tone

The Options menu (M2250 only) (2 line display)

Using features

Before you start

Basic call processing

Answering a call

Extending a call to an idle extension

Extending a call to a busy extension (with Camp-on)

Extending a call to a busy extension (with Hold)

Holding a call on a lpk key

Parking a call

Timed recall from an unanswered extended call

Timed recall from an unanswered parked call

Recall from an extension using LINK or ATT RECALL

Recall from an extension using Transfer

Recall from an extension using Conference

Recall to Same Attendant

Calling an extension

Calling an outside number

Trunk-to-trunk call

Through-dialing

Setting up a conference call

Calling another attendant

Transferring a call to another attendant

Break-in (post-dial)

Break-in (pre-dial)

Break-in (busy verify)

Sending a warning tone to an extension in line lockout

Requeueing a call to the next available attendant

Timed Reminder Recall

Centrex/Exchange Line Switchhook Flash

This document was created with FrameBuilder 4.0.2

Содержание Meridian M1250








































































































































































Результаты поиска

Содержание Meridian M1250

Отзывы:

Nortel Meridian M1250, Руководство пользователя, Страница: 2 / 168

Результаты поиска

Содержание Meridian M1250

Отзывы: