manualshive.com logo in svg

Nortel Meridian M1250, Руководство пользователя, Страница: 159 / 168

Поделиться
Скачать
Nortel Meridian M1250 Скачать руководство пользователя страница 159

 

• • • • 153 • • • •

 

Message Center

 

Taking a message

 

A call is forwarded to you when the original destination is busy or does not answer. You can leave a signal 
at the called extension, either during the call or when there is no call in progress, to indicate that a 
message is waiting.

 

1

 

A call is forwarded to 
you. Press the lpk key 
beside the flashing S 
indicator (or msg. ctr. 
ICI) to answer.

The tone stops. The lpk 
and S indicators go on 
steadily. The msg. ctr. ICI 
and msg. indicators are 
on.

 

2

 

Take the message. 
Determine whether it is 
intended for the 
displayed extension.

 

3

 

If the message is 
intended for the 
displayed extension, 
press msg. indic. If the 
message is not intended 
for the displayed 
extension, press msg. 
indic., dial a new 
extension, and press 
msg. indic. again. 

The msg.  indicator goes 
off. The MSG WAITING 
signal at the dialed 
extension goes on.

 

4

 

Press RLS to end the 
call.

The RLS indicator goes 
on; you are free to process 
other calls.

 

 

This document was created with FrameBuilder 4.0.2

Содержание Meridian M1250









































































































































































Отзывы:

Нет отзывов