Nortel Meridian M1250 Скачать руководство пользователя страница 143

Страница: 143 / 168

• • • • 137 • • • •

Charge

Entering an account number after dialing a call

Use this procedure to assign a charge account number to an outgoing call after you have dialed the call.

Note 1:

Charge account numbers may consist of up to 23 digits. The system ignores extra digits.

Note 2:

You can also enter charge account numbers before extending incoming calls to extensions.

Note 3:

During a conference call, you can:

— assign portions of the call to different accounts by entering charge numbers as you add

trunks to the conference

— assign the entire call to a single charge account number.

You have dialed an
outgoing call for an
extension at your
location. Press chg. [If
you do not have this key,
press conf. 6, dial SPRE
5, the charge account
code.]

The D indicator flashes;
the called party is
automatically placed on
hold. The charge indicator
goes on.

Dial the charge account
number.

The D indicator goes off;
the call is automatically
reestablished. The charge
indicator goes off.

Press RLS to end your
connection in the call.

The RLS indicator goes
on; you are free to process
other calls.

This document was created with FrameBuilder 4.0.2

Содержание Meridian M1250








































































































































































Результаты поиска

Содержание Meridian M1250

Отзывы:

Nortel Meridian M1250, Руководство пользователя, Страница: 143 / 168

Результаты поиска

Содержание Meridian M1250

Отзывы: