Nortel Call Recording Скачать руководство пользователя страница 83

Страница: 83 / 94

September 2007

Planning, Installation, and Administration Guide

0x3affe64 (): task deadrecordingDiskInit: created REC: volume (5 MB)

0x2a61d94 (tMaint): Init XA

0x2a61d94 (tMaint): XA : - Create MsgQ (Struct)

0x2a61d94 (tMaint): XA : - Register with M-1 Manager

0x2a61d94 (tMaint): XA : - Spawn xaTask()

0x2516b50 (tXA): Task Spawned OK

********** Initalising initAppGlob

serial number = d8d0489f

/C:/ - Volume is OK

0x2a61d94 (tMaint): XA : - Query 8051XA for Dongle ID

0x2a61d94 (tMaint): dspmInit : Initialising DSPM

0x2516b50 (tXA): Got Dongle Response

0x2516b50 (tXA): Dongle : 10237502

0x2516b50 (tXA): Got Version Response

0x2516b50 (tXA): Version : MC Firmware Rls 6.5

0x2516b50 (tXA): Serial Number not supported

0x250c0e8 (tDSPM): tDSPM suspended

0x2a61d94 (tMaint): xaToHostPollingEnable: XA to Host Polling Enabled.

0x243fa38 (tVpAppl): Task spawned.

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 83 / 94

Результаты поиска

Содержание Call Recording

Отзывы: