Nortel Call Recording Скачать руководство пользователя страница 69

Страница: 69 / 94

September 2007

Upgrade Procedures

Planning, Installation, and Administration Guide

XA firmware upgrade

There are three recommended methods for upgrading XA firmware.

1. “XA upgrade from an external FTP server,” on page 69.

2. “XA upgrade using PCMCIA card to transfer firmware to compact flash

card,” on page 70.

3. “XA upgrade using FTP to transfer firmware to compact flash card,” on

page 71.

Note:

XA Upgrades to the card require access to the VxWorks shell on the

bootROM load. This is available either through a telnet connection or
through serial access to COM1. For bootROM load shell access, the default
user name is itgadmin and the default password is itgadmin.

XA upgrade from an external FTP server

Use this procedure to upgrade XA from an external FTP server.

Ensure the XA firmware is loaded on an FTP server.

Reboot the card.

While the card reboots, when prompted, type

jkl

to access the bootROM.

Note:

The LAN cable must be connected into the other port on the

L-adapter for the network interface on the bootROM load to work
correctly.

Perform the upgrade by typing the following command at the shell:

upgradeXa "<server IP address>", "<userid>",

"<password>", "<path>", "<filename>" <CR>

The <userid> and <password> are those of the FTP server and the
<path> is the path to the file on the FTP server.

After the upgrade is complete, reboot the card.

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 69 / 94

Результаты поиска

Содержание Call Recording

Отзывы: