Nortel Call Recording Скачать руководство пользователя страница 38

Страница: 38 / 94

Configuring the Nortel Call Recording Card

Standard 1.0

Nortel Call Recording Card

Network settings

This section documents the Nortel Call Recording Card network settings.

Network speed/duplex setting

The Nortel Call Recording Card C-LAN interface auto negotiates its speed
and duplex settings. To verify these settings, execute the following
command from the maintenance command line interface:

->linkGetOperation 0

Result:

0x2a4eedc (tShell): T-LAN in Autonegotiation Mode

0x2a4eedc (tShell): T-LAN operating in 100Mbps, Full-

Duplex mode.

Note:

The

T-LAN shown in the output of the linkGetOperation command is

the C-LAN of the card.

Security settings

Nortel Call Recording Card uses a number of TCP/UDP ports to operate
correctly. These are documented in the following table.

Table 9:

TCP/UDP ports used

L4 Protocol
(TCP/UDP)

Port
Number Description

Comment

TCP

ftp

You can select another port
for FTP.

TCP

telnet

TCP

111

sunrpc-portmapper

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 38 / 94

Результаты поиска

Содержание Call Recording

Отзывы: