manualshive.com logo in svg

Nortel Call Recording, Руководство пользователя, Страница: 22 / 94

Поделиться
Скачать
Nortel Call Recording Скачать руководство пользователя страница 22

Configuring the Nortel Call Recording Card

Standard 1.0

22

Nortel Call Recording Card

Switch Configuration for Nortel Call 
Recording Card

The Nortel Call Recording Card has 32 ports. Of the 32 ports, 16 are 
configured as Live Monitor ports and 16 are configured as Observe ports.

Each Nortel Call Recording Card session can consist of two ports: a Live 
Monitor port to allow observers hear the calls as they occur and an observe/
record port to perform the recording. These ports must be established in 
pairs with the even number ports (units 0, 2, 4, 6 and so on) configured as 
live monitor ports and the odd numbers ports (units 1, 3, 5, 7 and so on) 
configured as observe/record ports. 

An example configuration of two Nortel Call Recording Card sessions has:

„

Unit 0 as a Live Monitor port with unit 1 as the corresponding Observe/
record port.

„

Unit 2 as a Live Monitor port with unit 3 as the corresponding Observe/
record port.

Note: 

If installing less than 16 Nortel Call Recording Card sessions, 

configure the required number of Live Monitor and observe/record ports 
only.

Live Monitor port configuration

Use overlays 11 and 32 to configure Live Monitor ports on the Nortel Call 
Recording Card.

Invoke Live Monitoring by using the following mechanism:

Содержание Call Recording































































































Отзывы:

Нет отзывов