Nortel Call Recording Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 94

Nortel Call Recording Скачать руководство пользователя страница 72

Upgrade Procedures

Standard 1.0

72

Nortel Call Recording Card

BootROM loadware upgrade

There are three recommended methods for upgrading bootROM loadware.

1. “BootROM loadware upgrade from an external FTP Server,” on page 72.

2. “BootROM loadware upgrade using PCMCIA Card to transfer loadware

to Compact Flash Card,” on page 73.

3. “BootROM loadware upgrade using FTP to transfer loadware to

Compact Flash Card,” on page 73.

BootROM loadware upgrades to the card require access to the VxWorks
shell on the bootROM load. This is available either through a telnet
connection or through serial access to COM1. For bootROM load shell
access, the default user name is itgadmin and the default password is
itgadmin.

BootROM loadware upgrade from an external FTP Server

1

Ensure the BootROM loadware firmware is loaded on an FTP server.

2

Reboot the card.

3

While the card reboots, when prompted, type

jkl

to access the bootROM.

Attention:

The LAN cable must be connected into the other port on the

L-Adapter for the network interface on the bootROM load to work
correctly.

4

At the shell, perform the upgrade by typing the following command:

upgradeBoot "<server IP address>", "<userid>",

"<password>", "<path>", "<filename>" <CR>

The <userid> and <password> are those of the FTP server and the
<path> is the path to the file on the FTP Server.

5

After the upgrade is complete, reboot the card.

«
...
70
71
72
73
74
...
»

Содержание Call Recording































































































Отзывы:

Нет отзывов