manualshive.com logo in svg

Nortel Call Recording, Руководство пользователя, Страница: 17 / 94

Поделиться
Скачать
Nortel Call Recording Скачать руководство пользователя страница 17

September 2007

Installing the Nortel Call Recording Card

Planning, Installation, and Administration Guide

17

Installing the Nortel Call Recording Card

Use the following preinstallation checklist to ensure you meet the Nortel 
Call Recording Card installation requirements.

Preinstallation checklist

To install the Nortel Call Recording Card, you must meet the installation 
requirements listed in Table 2: “Preinstallation checklist for Nortel Call 
Recording Card,” on page 17.

Table 2: 

Preinstallation checklist for Nortel Call Recording Card

Requirements for Nortel Call Recording Card installation

Check

Nortel Call Recording Card installation pack, see Table 7: 
“Nortel Call Recording Card product structure,” on page 32.

❒

RS232 maintenance cable for access to the command prompt of 
the card.

❒

Access to switch software with administrator privileges to 
configure the card at switch level. 

❒

The switch must have an available slot in which to install the 
card.

❒

IP configuration for the card: card IP address, gateway IP 
address and subnet mask. See  “Assigning the Internet Protocol 
(IP) address,” on page 40.

 

❒

FTP server configuration

FTP server with accounts set up for Nortel Call Recording Card. 
These accounts must have write and append access, see  
“Recording file format,” on page 45.

 

❒

Содержание Call Recording































































































Отзывы:

Нет отзывов