Nortel Call Recording Скачать руководство пользователя страница 65

Страница: 65 / 94

September 2007

Upgrade Procedures

Planning, Installation, and Administration Guide

7..18..19..20..21..22..23..24..25..26..27..28..29..30..31..

32..33..34..35..36..37..38..39..40..41..42..43..44..file

read complete

Program filename = /C:/exec

Checksum = 0xdef4797d

length = 0x59d1fc

Verifying checksum ...

Upgrade completed OK

Reboot the pack to run new loadware

The <userid> and <password> are those of the FTP server and the
<path> is the path to the file on the FTP Server.

After the upgrade is complete, enable the card from overlay 32 on the
switch software

Restart the card.

After the card is restarted, at the shell, type:

swVersionShow <CR

This command displays the current software version running on the card.
For example:

softwareRev: CRC Rel: 0.01

Loadware upgrade using the PCMCIA Card to transfer loadware
to the compact flash card

Use this procedure to upgrade the loadware from the local /C:/ drive
Compact flash card.

Disable the card using overlay 32 on the switch software.

Insert the PCMCIA card into the faceplate PCMCIA card slot.

Copy loadware from the PCMCIA card (/A:/ drive) to the compact flash
card (/C:/ drive) as shown in the following example:

copy("/A:/newexec","/C:/newexec")

The checksum value
varies between software
loads. Consult the release
notes for the applied
upgrade load to identify
the correct value.

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 65 / 94

Результаты поиска

Содержание Call Recording

Отзывы: