Nortel Call Recording Скачать руководство пользователя страница 68

Страница: 68 / 94

Upgrade Procedures

Standard 1.0

Nortel Call Recording Card

Opening file /C:/newexec

File /C:/newexec opened

File Length = 0x0059d1fc

Bank Size = 0x00780000

Updating sector:

0..1..2..3..4..5..6..7..8..9..10..11..12..13..14..15..16..1

7..18..19..20..21..22..23..24..25..26..27..28..29..30..31..

32..33..34..35..36..37..38..39..40..41..42..43..44..file

read complete

Program filename = /C:/exec

Checksum = 0xdef4797d

length = 0x59d1fc

Verifying checksum ...

Upgrade completed OK

Reboot the pack to run new loadware.

After the upgrade is complete, remove the original loadware file that was
transferred onto the card by typing the following command from the shell:

rm "/C:/newexec" <CR>

Where "C:/newexec" is the location of the file copied to the compact flash
card.

Enable the card using overlay 32 on the switch software.

Restart the card.

After restarting the card, type the following command from the shell:

swVersionShow <CR>

This command displays the current software version running on the card,
for example:

softwareRev: CRC Rel: 0.01

The checksum value
varies between software
loads. Consult the release
notes for the applied
upgrade load to identify
the correct value.

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 68 / 94

Результаты поиска

Содержание Call Recording

Отзывы: