Nortel Call Recording Скачать руководство пользователя страница 80

Страница: 80 / 94

Standard 1.0

Nortel Call Recording Card

Setting tLogTask priority to 250

Found device : Cirrus CL-PD672x

0x3affe64 (tRootTask): PC Card Detected: Socket 1

logTask: 2 log messages lost.

ipMethodInit, gIPMethod = 2

IP Address from NVRAM: 47.166.107.144

IP Data in NVRAM Valid, Boot Line updated

IP Address:47.166.107.144

Gateway Address:47.166.107.190

Subnet Mask::ffffffc0

Host Name: bootHost

Target Name: vxTarget

User: defuser

MAC Address for Port 0 is : 00:20:d8:d0:48:9e

SysConf: uEng_intConnect to pktHandlingIsr.

0 symbols bound.

Load uCode from buffer Status : Return Success

Starting Microengines.

0x3affe64 (tRootTask): Loading MAC_21440...

0x3affe64 (tRootTask): mac21440Load: Init String[0] NULL: ixpMac

0x3affe64 (tRootTask): Loading MAC_21440...

0x3affe64 (tRootTask): MAC 21440 String : Processed all arugments

0x3affe64 (tRootTask): mac21440InitMem: Net Pool ID is 49099716

0x3affe64 (tRootTask): Done loading mac21440...

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 80 / 94

Результаты поиска

Содержание Call Recording

Отзывы: