Nortel Call Recording Скачать руководство пользователя страница 32

Страница: 32 / 94

Configuring the Nortel Call Recording Card

Standard 1.0

Nortel Call Recording Card

Cabling the Nortel Call Recording Card

Use this section to connect the Nortel Call Recording Card cables.

Introduction

The Nortel Call Recording Card installation pack contains the following
items.

Table 7:

Nortel Call Recording Card product structure

The 32-port media card comes with the dongle and the compact flash with
the Nortel Call Recording Card load preinstalled (the C:/exec file on the
Compact Flash card). Figure 4: “Media card layout,” on page 33 shows the
layout of the Media Card.

Part #

NT Code

Description

A0888965

NTVQ01BA

32 port media card

A0852632

Shielded 50 pin key telephone to 9D sub and
twin RJ45 adapter (L-Adapter)

A0870556

NTVQ83AA

ITG EMC shielding kit

A0783483

NTCW84JA

M1 backplane to 50-pin I/O panel cable
(filter block)

N0056092

NT9S80MA

Compact flash with Nortel Call Recording
Card application load

Security device (dongle)

Содержание Call Recording































































































Результаты поиска

Содержание Call Recording

Отзывы:

Nortel Call Recording, Руководство пользователя, Страница: 32 / 94

Результаты поиска

Содержание Call Recording

Отзывы: