manualshive.com logo in svg

Nortel Call Recording, Руководство пользователя, Страница: 73 / 94

Поделиться
Скачать
Nortel Call Recording Скачать руководство пользователя страница 73

September 2007

Upgrade Procedures

Planning, Installation, and Administration Guide

73

BootROM loadware upgrade using PCMCIA Card to transfer 
loadware to Compact Flash Card

Use this procedure to perform a BootROM loadware upgrade using 
PCMCIA Card to transfer loadware to Compact Flash Card.

1

Reboot the card.

2

While the card reboots, when prompted, type 

jkl

 to access the bootROM.

3

Insert the PCMCIA card into the faceplate PCMCIA Card slot.

4

Copy loadware from the PCMCIA card (/A:/ drive) onto the compact flash 
card (/C:/ drive) as shown in the following example:

copy("/A:/filename","/C:/filename")

5

Remove the PCMCIA card from the faceplate slot.

Note: 

Do not insert a card in the /A:/ drive when the Nortel Call 

Recording Card is in normal operation.

6

At the shell, perform the bootROM, by typing the following command:

upgradePCMCIABoot "/C:/bootROM"<CR>.

Where <Server IP Address> is the IP address of the Nortel Call 
Recording Card. <userid> and <password> are the same as the shell 
user name/ password on the Nortel Call Recording Card. <path> is the 
location on the card where the bootROM loadware is located.

7

After the upgrade is complete, reboot the card.

BootROM loadware upgrade using FTP to transfer loadware to 
Compact Flash Card

Use this procedure to perform a BootROM loadware upgrade using FTP to 
transfer loadware to Compact Flash Card.

1

FTP the bootROM loadware onto the /C: drive using the same method as 
outlined previously for transferring the application load.

2

Reboot the card.

3

While the card reboots, when prompted, type 

jkl

 to access the bootROM.

Содержание Call Recording































































































Отзывы:

Нет отзывов