Nordson VersaBlue 100H/100H Скачать руководство пользователя

Страница: 11 / 108

Safety

1-1

2004 Nordson Corporation

A1EN

−

[XX

−

SAFE]

−

Section 1

Safety

Read this section before using the equipment. This section contains

recommendations and practices applicable to the safe installation,

operation, and maintenance (hereafter referred to as “use”) of the product

described in this document (hereafter referred to as “equipment”).

Additional safety information, in the form of task-specific safety alert

messages, appears as appropriate throughout this document.

WARNING:

Failure to follow the safety messages, recommendations, and

hazard avoidance procedures provided in this document can result in

personal injury, including death, or damage to equipment or property.

Safety Alert Symbols

The following safety alert symbol and signal words are used throughout this

document to alert the reader to personal safety hazards or to identify

conditions that may result in damage to equipment or property. Comply with

all safety information that follows the signal word.

WARNING:

Indicates a potentially hazardous situation that, if not avoided,

can result in serious personal injury, including death.

CAUTION:

Indicates a potentially hazardous situation that, if not avoided,

can result in minor or moderate personal injury.

CAUTION:

(Used without the safety alert symbol) Indicates a potentially

hazardous situation that, if not avoided, can result in damage to equipment

or property.

Содержание VersaBlue 100H/100H













































































































Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды

Nordson VersaBlue 100H/100H, Руководство пользователя

Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды