Nordson VersaBlue 100H/100H Скачать руководство пользователя

Страница: 91 / 108

Repair

7-11

P/N 7146386A

2008 Nordson Corporation

VBN w/o Control System

Calibrating

CAUTION:

When calibrating, keep hands or conducting tools away from

coaxial connections (10, 11, Fig. 7-12) to prevent distortion of the signal.

Prerequisites:

Level sensor is installed, fastened mechanically and connected

electrically (observe color of sensor cable)

Tank empty

Level sensor is clean

Operating voltage is applied (LED

Operating voltage

(1, Fig. 7-12) lit).

1. Plug jumper

Calibration

(4) into position

2. With potentiometer

(2), find the switching point of the LED

Calibration

(3) (LED just lights up).

Turn clockwise: LED on
Turn counterclockwise: LED off

3. Plug jumper

Calibration

(4) into position

4. With potentiometer

(5), find the switching point of the LED

Calibration

(3) (LED just lights up).

Turn clockwise: LED on
Turn counterclockwise: LED off

5. Plug jumper

Calibration

(4) into position

(center) to switch off the LED

Calibration

Fig. 7-13

The evaluator is now ready for operation.

NOTE:

The LED

Reference section

(9, Fig. 7-12) lights up as soon as the

reference section (area between the lower inactive section and the sensor

measuring range) is covered with material.

Содержание VersaBlue 100H/100H













































































































Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды

Nordson VersaBlue 100H/100H, Руководство пользователя

Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды