Nordson VersaBlue 100H/100H Скачать руководство пользователя страница 44

Страница: 44 / 108

Outputs

Inputs

Installation

3-12

P/N 7146386A

2008 Nordson Corporation

VBN w/o Control System

Interface Assignment

Interface Standard I/O

−

Standard Assignment for XS 2

−

General Information

To conform with a European standard regarding electro-magnetic
compatibility (EMC), only shielded cable may be connected. The shield
must

be connected to ground in compliance with the standard regarding

electromagnetic compatibility.

Inductive loads (e.g. solenoid valves) connected to the melter must be

equipped with a protective device (e.g. recovery diode) that disables the

inductive voltage generated when an inductive load is switched off.

The permitted voltage deviation is

10%.

Digital inputs

Pin

Input

Feature

24 V

Internal (melter)

0 V

External (customer’s)

NOTE:

Customer connects his reference potential here, if 24 V

is provided by

customer.

Melter enable

Main contactor

Ready

Unit not ready

Fault indication

No fault indication

optional

Interfaces for Internal/External Pressure Sensors

The pressure sensors are connected to the terminal strip XLD. Refer to

wiring diagram.

Содержание VersaBlue 100H/100H













































































































Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды

Nordson VersaBlue 100H/100H, Руководство пользователя

Результаты поиска

Содержание VersaBlue 100H/100H

Отзывы:

Похожие инструкции для VersaBlue 100H/100H

Бренды по названию

Популярные бренды